Schottky barrier diodes (SBDs) play a critical role in power converters. The monolithic integration of gallium nitride (GaN) SBDs and power HEMT devices can lead to compact power ICs. In this article, we summarize a novel design improvement that enhances the performance of a GaN SBD while being compatible with the standard HEMT process flow.
Key SBD requirements
An efficient SBD is required to meet several key characteristics, some of which are outlined below:
- A low on-state voltage (VT): This enables improved dead-time optimization in a converter and better trade-offs between conduction-loss reduction during 3rd-quadrant operation and switching robustness.
- Low on-state resistance (RON): Also helps minimize conduction losses. Dynamic stability of RON from switching between a high-bias off-state and the on-state is also important to ensure robustness over the application-specific system lifetime.
- Low reverse leakage: In wide bandgap (WBG) and ultra-wide bandgap (UWBG) semiconductors such as SiC, GaN, and gallium oxide (Ga2O3), high surface electric fields can cause high reverse currents from tunneling across the metal/semiconductor interface. While a higher Schottky barrier height at this interface can help minimize leakage, it results in a higher VT. Thus, a tradeoff is typically needed between these two metrics.
- High temperature operation: SBDs typically have a positive temperature coefficient in RON. While this can make device paralleling easier, it results in higher conduction losses and can force greater current through the main power device body diode (in the case of MOSFETs).
- Low junction capacitance: The unipolar nature of SBDs means that they do not suffer from reverse-recovery losses seen in p-n diodes. However, charging/discharging an SBD’s junction capacitance adds to net circuit switching losses.
- Surge capability: This is one metric where p-n diodes are superior. Solutions include a merged p-i-n junction in parallel to the SBD (MPS diodes).
p-GaN-terminated AlGaN/GaN SBD
Hung-Chun Chen and colleagues at the National Yang Ming Chiao Tung University, Taiwan, demonstrated a novel AlGaN/GaN SBD [1] that optimizes some of the above-mentioned metrics using a novel p-GaN termination approach.
The basic structure of the SBD is compatible with a standard p-GaN gate HEMT technology platform. The SBD design was implemented on QST-engineered substrates, which have been shown to yield several advantages in lower wafer stress and defects even when thick buffer layers are required.
In this case, an 8 µm-thick GaN buffer layer was grown on the AlN nucleation/Si(111) bonding layer used on the QST substrate, followed by a 1-µm-thick carbon-doped GaN layer. A 20-nm GaN channel layer was next grown, followed by a 12-nm-thick AlGaN barrier layer and a 2-nm-thick AlN etch stop layer.
The 80-nm-thick p-GaN gate layer for the HEMT and the SBD terminations was grown over this AlN layer. The use of the AlN etch stop was shown to give a much smoother post-p-GaN etch wafer surface, as it prevents over-etching into the AlGaN barrier layer.
The anode of this AlGaN/GaN SBD is over the AlGaN barrier layer, while the cathode connects to the two-dimensional electron gas (2-DEG) formed in the GaN channel at the AlGaN/GaN interface.

Three different edge termination schemes were tried for the SBD, as depicted in Figure 1.
Sample A only had a p-GaN anode edge termination. Samples B and C had cathode terminations consisting of 3 and 5 cathode-connected p-GaN islands, respectively. The SBDs used an anode-to-cathode distance (LAC) of either 5 or 20 µm.
Results and analysis
The forward characteristics of all three SBDs showed similar VT values of around 0.7 V at 25 °C and 0.54 V at 150 °C. Good VT stability was seen under a positive anode voltage (VAC) stress of up to 5 V. At a VAC of 7 V, a negative shift in VT is seen for all three devices, since they have the same anode edge termination.
This positive bias instability (PBTI) is similar to that seen in p-GaN gate HEMT devices, and is thought to result from hole injection and trapping from the p-GaN into the AlGaN barrier, which can induce a higher 2-DEG density and hence lower VT.
Adding cathode p-GaN island terminations increases device RON, as shown in the parametric summary table in Figure 2. This is expected because the 0-biased GaN cathode terminations reduce the 2-DEG at the AlGaN/GaN interface in this forward SBD mode.
As expected, the reverse characteristics show an increase in breakdown voltage (BV) when LAC is increased from 5 µm to 20 µm. The breakdown voltages at an LAC of 5 µm were around 1000 V and increased when using an LAC of 20 µm to above 1500 V, as shown in Figure 2.

At LAC = 20 µm, samples B and C with the cathode terminations show a marked improvement in BV over that seen with Sample A. The best-performing Sample C had a BV exceeding 2000 V. The mechanism for this BV increase in the p-GaN cathode-connected samples is thought to be similar to that seen with the hybrid drain embedded gate injection transistor (HD-GIT).
Here, it was shown that a p-GaN layer placed on the AlGaN barrier that is physically connected to the drain of the GaN HEMT device suppresses electron trapping, which is the major cause of current collapse and BV degradation at high drain fields in the HEMT device. The p-GaN layer injects holes that neutralize the trapped electrons, resulting in a dynamically stable device.
A major advantage seen in the use of the p-GaN cathode edge termination is in the dynamic RON performance of the SBDs. As shown in Figure 3, Sample A with just the anode termination sees an RON increase of greater than 200% with a 1000 V stress.

The cathode-connected p-GaN-terminated devices show a more stable RON. Sample B with three p-GaN-terminated cathode islands shows an RON increase of 69%, while sample C (with the five-island configuration) actually sees an RON decrease of around 46%. Hence, it is shown that the level of hole injection can effectively be tuned to flatten dynamic RON, leading to a more stable device.
This stability outweighs the increase in the time-zero RON from the use of the cathode termination and can allow the designer to use a smaller device or target a smaller RON for the same size needed when compared to an unterminated device accounting for its dynamic RON increase.
Cover image: Adobe Stock
References
Source: Power Electronics News








