This Design Idea describes how a critical in-flight power supply unit issue was analyzed and resolved successfully.
The circuit described in this Design Idea is part of a spacecraft power supply unit designed to operate in the harsh radiation environment of Jupiter, where the level of cosmic radiation is exceptionally high. The block diagram of the power supply system is shown in Figure 1.

Figure 1 This blog diagram describes the power supply for a spacecraft designed for high cosmic radiation environments such as in proximity to Jupiter.
The unit contains two IRHNJ57024 N-channel MOSFETs. A radiation-hardened version of this device is the JANSR2N7480U3. The power supply provides the regulated voltages required by the onboard sensors. The nominal 28 V input voltage is converted into +5 V, +3.3 V, and −5 V output voltages to satisfy the sensors’ power requirements.
Wow the engineering world with your unique design: Design Ideas Submission Guide
The most critical section of the power supply circuit is shown in Figure 2. This section is responsible for the primary power conversion and must maintain reliable operation under the extreme environmental conditions encountered during the mission.

Figure 2 This schematic details the most critical section of the power supply circuit.
The PWM controller drives two N-channel MOSFETs via a gate-drive transformer. These MOSFETs control the power delivered to transformer T1501, which provides energy to the load. Galvanic isolation between the PWM controller and the switching stage protects the input circuitry against failures in the power stage.
During the turn-off interval of the MOSFETs, energy stored in leakage inductances of transformer T1501 is recovered and returned to the DC-link (buffer) capacitors, thereby improving the converter’s efficiency.
The power ground (NIM_PGND) and the PWM ground (DGND_DPU) are galvanically isolated from each other. This isolation protects the PWM circuitry from voltage spikes and electrical noise generated in the power stage, preventing disturbances that could affect its operation.
The switching of the MOSFETs can generate high-amplitude voltage spikes and transient noise on the power ground due to parasitic inductances and high di/dt currents. The snubbers were optimized based on measurements to suppress the effects of leakage inductance and parasitic capacitance.
The PWM controller includes a voltage-feedback input (VFB) and a current-sense input (ISEN), which are used to regulate the output voltage and implement current limiting. The RAMP_NIM2 signal is proportional to the total output current and is fed back to the PWM controller.
And now we come to the critical event alluded to in the earlier subhead. After launch, additional testing of the MOSFETs was performed. The results showed that the manufacturing lot of the N-channel MOSFETs used in the design was sensitive to high-dose-rate (HDR) radiation. Degradation was observed when the dose rate exceeded 50 rad(Si)/s, even though the devices were qualified for a total ionizing dose (TID) of up to 100 krad(Si).
Exposure to HDR radiation resulted in a reduction of the MOSFET threshold voltage (Vth) of approximately 45%. According to the datasheet, the VGS(th) gate threshold voltage is between 2.0 and 4.0 V. With a nominal threshold voltage of 2.0 V, a 45% reduction would lower Vth to approximately 1.1 V.
The resulting impact on the switching behavior and reliability of the circuit therefore needed to be evaluated. The investigation was based on PSpice simulations of the circuit, in which the MOSFET threshold voltage parameter, VGS(th), was varied over a wide range and reduced down to 0.5 V (Figure 3).

Figure 3 Simulation with VGS(th)=0.5V shows that the +5 V, +3.3 V, and −5 V supply voltages are nominal (upper section), while the lower section graphs the gate voltages of the MOSFETs.
The simulation results fortuitously demonstrated that the circuit continued to operate correctly without failure even at significantly lower VGS(th) values. Specifically, since the MOSFETs operate here as switching devices, the reduction in VGS(th) does not prevent proper circuit operation. However, if the MOSFETs were operated in a linear application, the impact of the threshold-voltage shift could be significantly different.
Janos Nagy is a senior electronics engineer specializing in scientific instrumentation, embedded systems, power electronics and space hardware. Beginning in 1977, he has worked at the KFKI Institute for Particle and Nuclear Physics, now part of the Wigner Research Centre for Physics. And since 2021, he has also been affiliated with the Centre for Energy Research.
Source: EDN







